Airspool EZ Connect 12K and Plug In Solar Kit
$4,560.00
-
Airspool MS12 Quick ’n’ Easy solar mini-split plus two APsystems EZ1-LV plug-in microinverters, an APmeter zero-export meter, eight panels, ground-mount racking and wiring.
- Mini-split: 12,000 BTU heat pump, 22.5 SEER2, 120V, runs on solar first
- Plug-in solar: 2 × 900VA microinverters into standard 120V outlets
- Includes: 8 panels (your choice), 2 BrightMount racks, PV disconnect, PV wire
Solar Air Conditioning · Plug-In Solar
Airspool EZ Connect 12K Mini-Split + Plug-In Solar Kit
A 12,000 BTU Airspool heat pump that runs directly on solar, plus two APsystems plug-in microinverters that send the rest of your solar to your home through a standard 120V outlet, and an APmeter that keeps that solar from exporting to the grid. Eight panels, ground-mount racking and the wiring are included.
12,000 BTU
Heating & cooling, ~500 sq ft
8 × 400W
4 for the mini-split, 4 for plug-in solar
Up to 1,800VA
Plug-in solar output (2 × 900VA)
Zero export
APmeter keeps plug-in solar in your home
Two Ways This Kit Uses Solar
1. Direct to the mini-split
About 4 panels connect straight to the Airspool’s DC solar input (Airspool recommends about 1,500W). The unit runs on sun first and fills in from the grid automatically — no batteries or inverter.
2. Plug-in solar for the home
The other 4 panels connect to the two EZ1-LV microinverters (2 panels each). Each plugs into a 120V outlet and offsets daytime use of everything else in your home.
Zero-Export Control with the APmeter
How it works
The APmeter and its CT clamp mount in your electrical panel and measure what your home is using. Through the AP EasyPower app it continuously adjusts the EZ1-LV output so production stays at or below your home’s use.
Why it matters
Many utilities don’t allow plug-in solar to send power back to the grid. Zero-export control keeps every watt in your home and helps meet those rules.
Setup
Install the meter and CT clamp at the panel, connect it to Wi-Fi, pair it with the EZ1-LV units and turn on export limiting in the app. Have a qualified electrician install anything inside the panel.
Keep the two paths separate
The EZ1-LV outputs AC through a plug; the mini-split takes DC from its own panels. Wire each set of panels to its own device — don’t combine them in one string.
What’s Included
Airspool MS12 Specifications
APsystems EZ1-LV Specifications
Panel & Wiring Guidance
- Mini-split string: 4 × 400W panels (about 1,600W) feed the Airspool’s solar input, close to Airspool’s ~1,500W recommendation.
- EZ1-LV inputs: one 400W panel per input (two per microinverter), within the 315–660W range and 60V limit.
- Outlets: plug each EZ1-LV into a 120V outlet on a circuit that isn’t heavily loaded, and keep the mini-split on its own 15A outlet.
Good to know
Plug-in solar rules vary by state and utility — check with your utility and local building department (AHJ) before connecting; the included APmeter provides zero-export control where it’s required. The APmeter needs Wi-Fi to control the EZ1-LV units. The EZ1-LV is not for rooftop mounting, and it shuts off during a grid outage. The mini-split runs on direct solar during an outage when the sun is out. Concrete for the ground-mount footings is not included.
Datasheets / manuals / wiring diagrams
Spec Sheet –
24KBTU_user_manual
plug_in_microinverter_spec_sheet
