Tamarack Solar 2″ Tee Fitting 89761
$50.00
Racking and Mounting
Showing 33–48 of 78 resultsSorted by popularity
-
-
-
Simple Tilt Knee, Set for K2 Simple Tilt System
$20.00A tilt adjustment accessory for the K2 CrossRail Simple Tilt System, the K2 Systems Simple Tilt Knee Set provides an integrated bracket and hardware that enable fixed tilt angles on solar rail installations, making it easier and faster to achieve optimized panel tilt on flat or low-slope roofs.
-
Tamarack Solar Ground Mount Kit 90804 for 4 Add Column KIT B 93″ Rails
$478.75The Tamarack Ground Mount System is assembled using 3.1 rail with 2-inch schedule 40 or 80 galvanized steel pipe that is purchased separately. The system comes with all parts needed except for the pipe and concrete. Assembly is quick and easy and can be used on almost any terrain.
-
Integra 10 Pack BoltsIR-T1 TileBallast No Penetration Tile Roof Mounting System
$129.99The IntegraRack IR-T1 TileBallast™ is a groundbreaking tile-roof mounting bracket that requires no tile removal and no roof penetration, offering a fully non-invasive solution for concrete tile roofs. Instead of screwing through tiles, the IR-T1 uses IntegraGel industrial-strength epoxy to bond three overlapping concrete tiles together, leveraging their weight as ballast. This system dramatically speeds up installation (up to 4× faster than traditional tile hooks), while also increasing structural strength. Tested in a wind tunnel at over 165 MPH (3:1 safety factor), the IR-T1 is built to withstand severe wind conditions without compromising roof integrity. It includes an integrated upright mount that supports any rail system, making it highly flexible for solar module installation.
-
-
S-5! SolarFoot Brackets Attachment For Metal Roofs
$6.99S-5! SolarFoot Brackets Attachment For Metal Roofs
-
-
Tamarack Solar Ground Mount Kit 90798 for 4 First Column KIT A 93″ Rails
$550.00Tamarack Ground Mount System Tamarack Solar Ground Mount Kit 90798 for 4 First Column KIT A 93″ Rails [tabs slidertype=”top tabs”] [tabcontainer] [tabtext]Description[/tabtext] [tabtext]Documents[/tabtext] [tabtext]Videos[/tabtext] [tabtext]Warranty[/tabtext] [/tabcontainer] [tabcontent] [tab] Introducing…
-
K2 Systems Conduit Clamp CrossRail Kit
$4.40A stainless steel conduit management clamp for K2 CrossRail mounting systems, the K2 Conduit Clamp CrossRail Kit attaches into the rail’s side channel with included T-Bolt hardware and provides a quick, secure way to route and support conduit using a tool-less snap-fit design.
-
IntegraRack IR-IGSE1009 IntegraGel Fast Setting Structural Epoxy
$22.50The IntegraRack IR-T1 TileBallast™ is a groundbreaking tile-roof mounting bracket that requires no tile removal and no roof penetration, offering a fully non-invasive solution for concrete tile roofs. Instead of screwing through tiles, the IR-T1 uses IntegraGel industrial-strength epoxy to bond three overlapping concrete tiles together, leveraging their weight as ballast. This system dramatically speeds up installation (up to 4× faster than traditional tile hooks), while also increasing structural strength. Tested in a wind tunnel at over 165 MPH (3:1 safety factor), the IR-T1 is built to withstand severe wind conditions without compromising roof integrity. It includes an integrated upright mount that supports any rail system, making it highly flexible for solar module installation.
-
IntegraRack IR-45ASA Adjustable Seasonal Angle BallastRack™ Solar Module Racking System | 1 Adjustable Leg
$199.99The IntegraRack IR-45ASA BallastRack™ is a flexible, high-performance ground-mount racking system engineered to let you seasonally adjust your panel tilt between 15° and 45°. Built from 6061-T6 aircraft-grade aluminum (or optionally black zinc-plated high-strength steel), this system allows each panel’s angle to be tuned independently. It mounts without concrete footings, post-driving, or augers — using a variety of ballast or anchor options. Frames assemble in ~2 minutes and deliver excellent clearance, high wind and snow load resilience, and low installed cost per watt.
-
IntegraRack IR-40FSA BallastRack Fixed Adjustable Angle Solar Module Rack
$139.99The IntegraRack IR-40FSAB BallastRack™ is a high-performance ground-mount racking system engineered for maximum flexibility in tilt angle and site conditions. Constructed from high-strength steel with a black zinc plating, the IR-40FSAB offers fixed-adjustable tilt from 15° to 40° in 2.5° increments — allowing you to optimize for annual solar production while maintaining structural durability. This system supports a variety of ballast or mounting methods (e.g., sandbags, water tanks, concrete curb stops, or anchor spikes), so you can install without poured concrete footings. The modular, “U”-shaped frame design enables fast assembly in ~2 minutes, while full row installation (frame + ballast + modules) can be completed in about 10 minutes per module, significantly reducing labor. It’s UL-2703 certified for bonding and mechanical strength, making it reliable and code-compliant for residential or commercial solar projects.
-
Solar Stack DAP Stormbond 2
$750.00The DAP StormBond 2 Roof Tile Adhesive is a high-performance two-component polyurethane foam adhesive engineered for heavy-duty bonding of solar pedestal systems and roof tile applications. Ideal for use in the Solar Stack mounting system, StormBond 2 delivers exceptional bond strength, superior durability and rapid cure time — enabling safer, faster solar installations without penetrating the roof substrate. Designed for commercial and residential low-slope or tile roofs, StormBond 2 ensures your solar mounting system remains securely attached, even under high wind loads and rigorous code conditions.
-
Solar Stack DAP Adhesive Cleaner (Cold Weather)
$29.99The Solar Stack DAP Adhesive Cleaner (Cold Weather) is a professional-grade solvent cleaner formulated to safely and efficiently remove uncured or excess adhesive from Solar Stack foam systems and applicator tools used in cold climates. Specifically engineered to work with Solar Stack SS-CW (Cold Weather) Foam Adhesive and the DAP Sharpshooter XP Applicator, this cleaner ensures smooth operation, reduced clogging, and longer tool life, even in low-temperature conditions.
-
End of content
End of content
Integra BallastRack IR-30 Racking System (Single Frame)